Welcome to AWS Edition 2 - Errata List

 

 

RSS feed Print Button

Suggestion Form

Complete Errata Listing

AWS Section AWS Page AWS Item # Errata Description Date Errata Posted

 

Link Original Suggestion #
1 32 1.4.5.1.16 Change shaded 3 in 3.1.16 to read 5.1.16 7/31/15   2079
2 42 2.4.4.1.1.3 Change text from “room” to “broom”. 12/31/14   2040
2 42 2.4.4.1.1.1 Correct text by adding a space after the comma. 12/31/14   2041
3 62 3.4.6.9.1 Change the text to read “. . . pieces, and:” 12/31/14   2006
3 62 3.4.6.9.1.1 - New Add new Item: “Boards wider than stated widths shall default to the next greatest width and length requirement,” 12/31/14   2006
4 90 4.4.4.6 Change “LAY-UP” to “LAYUP” 12/31/14   2042
4 105 4.4.15.1.1 Change the text to read “. . . species or:” 12/31/14   2025
4 105 4.4.15.1.1.1 - New

Add new Item: “Any independently tested material that maintains panel flatness as set forth in this standard.”

12/31/14

  2025
4 105 4.4.16.1.6 Correct text to read “. . . minimum of 0.020” (0.51 mm) . . . “

12/31/14

  2052
5 120 5.4.5.1 Change to read: BACK PRIMING/SEALING OF CONCEALED SURFACES. 7/31/15   2077
5 121 5.4.6.14.2.1 Add brackets [] around the wording “Wash coat”: [Wash coat] . . . . 7/31/15   2077
5 122 5.4.6.14.3.1 Add brackets [] around the wording “Wash coat”: [Wash coat] . . . . 7/31/15   2077
5 122 5.4.6.14.3.7 Eliminate this Item and its line of text. 12/31/14   2004
5 122 5.4.6.15.1.1.1 Add brackets [] around the wording “Wash coat, nitrocellulose”: [Wash coat, nitrocellulose] . . . . 7/31/15   2077
5 122 5.4.6.15.1.1.2 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . 7/31/15   2077
5 122 5.4.6.15.1.2.1 Add brackets [] around the wording “Wash coat, nitrocellulose”: [Wash coat, nitrocellulose] . . . . 7/31/15   2077
5 122 5.4.6.15.1.2.2 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . . 7/31/15   2077
5 122 5.4.6.15.1.2.8 Add brackets [] around the wording “Second topcoat”: [Second topcoat] . . . . 7/31/15   2077
5 122 5.4.6.15.2.1.1 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . . 7/31/15   2077
5 122 5.4.6.15.2.2.1 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . . 7/31/15   2077
5 122 5.4.6.15.4.1.1 Add brackets [] around the wording “Wash coat, reduced conversion varnish”: [Wash coat, reduced conversion varnish] . . . . 7/31/15   2077
5 122 5.4.6.15.4.1.2 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . . 7/31/15   2077
5 123 5.4.6.15.4.2.4 Add brackets [] around the wording “Filler”: [Filler] . . . . 7/31/15   2077
5 123 5.4.6.15.6.1.1 Add brackets [] around the wording “Wash coat, vinyl”: [Wash coat, vinyl] . . . . 7/31/15   2077
5 123 5.4.6.15.6.1.2 Add brackets [] around the wording “Wash coat, vinyl, catalyzed”: [Wash coat, vinyl, catalyzed] . . . . 7/31/15   2077
5 123 5.4.6.15.6.2.5 Add brackets [] around the wording “Filler”: [Filler] . . . . 7/31/15   2077
5 123 5.4.6.15.7.1.1 Add brackets [] around the wording “Wash coat, acrylic”: [Wash coat, acrylic] . . . . 7/31/15   2077
5 123 5.4.6.15.7.2.4 Add brackets [] around the wording “Filler”: [Filler] . . . . 7/31/15   2077
5 124 5.4.6.15.9.1.1 Add brackets [] around the wording “Wash coat, reduced vinyl sealer”: [Wash coat, reduced vinyl sealer] . . . . 7/31/15   2077
5 124 5.4.6.15.9.2.3 Add brackets [] around the wording “Filler”: [Filler] . . . . 7/31/15   2077
6 138 Center Text Paragraph Change 2540 to 3048 04/29/16   2071
6 151 6.4.5.11.1.3 Change text to read: “. . . in thickness.” 12/31/14   2024
6 162 6.6.4.8.3.1 & 2 Bold the last digit of the Items reference number. 12/31/14   2010
7 182 7.4.7.8.6 - Corrected Change the Item number from “7.4.7.6” to “7.4.8.6”. 12/31/14   2037
7 184 7.6.4.2 - Corrected Change numbering of second and third indented Item under 7.6.4.2 and subsequent indented items. 12/31/14   2011
8 197 n/a Change second from bottom paragraph to read: “. . . leaf match and panel width therefore premanufactured sets shall not be used for sequenced custom and blueprint sequenced panels. 12/31/14   2003
8 216 8.4.5.6.2.1 Change from “HPHA” to HPVA” 7/31/15   2072
8 216 8.4.5.7.1 Change from “HPHA” to HPVA” 7/31/15   2072
8 218 8.4.5.13.4 Change to read: "If FLAME SPREAD RATED: 04/29/16   2114
8 218 8.4.5.13.4.1X Change to read: "Shall be of the construction standard of the panel manufacturer and conform to the requirements of applicale labeling agencies." 04/29/16   2114
8 218 8.4.5.13.7.2 Change to read: "If FLAME SPREAD RATED: 04/29/16   2114
8 218 8.4.5.13.7.2.1 Change to read: "Shall be of the construction standard of the panel manufacturer and conform to the requirements of applicable labeling agencies." 04/29/16   2114
8 218 8.4.5.13.8.1 Change text to read: “. . . or less in any face . . .” 12/31/14   2009
8 218 8.4.5.13.8.2 Change text to read: “. . . (6.4 mm) in any face . . .” 12/31/14   2009
8 224 8.4.7.6.11 Remove the word "MITERED". 04/29/16   2116
8 230 8.6.2.3.1 - Corrected Change Item numbering so that the first indent after Item 8.6.2.3 reads 8.6.2.3.1 and then correct all of the subsequent numbering through the end of Item 8.6.2.3. 12/31/14   2012
9 242 Center Column, Second paragraph Eliminate last sentence which reads "Misalignment of up to 3/8" (9 mm) is permitted in every Grade."Change to read: "If FLAME SPREAD RATED: 04/29/16   2103
9 247 Left Column, Last Paragraph Eliminate last paragraph which reads: "Because of warpage and twist characteristics of heavy, one piece, solid hardwood members, that method of construction is not recommended for stile and rail door construction." 04/29/16   2098
9 248 Bottom Left Illustration Change recommended stile width from 4-1/2” to 5” (127 mm) and change recommended 9” bottom rail to 10” (254 mm). 04/29/16   2104
9 251 9.1.9.3 Change text to read: “. . . EDGES on 20, 45, 60 . . . “ 12/31/14   2001
9 256 9.4.4.18 Change all subsequent shaded reference to “10” below to “18” – for a total of four occurrences. 7/31/15   2073
9 267 9.4.6.9.2.2 Change text to read: “. . . honey comb or expandable paper core, and . . .” 12/31/14   2002
9 267 9.4.6.9.2.2.1.2 Change text to read: “Top and bottom horizontal edges shall be as specified or as needed to meet WDMA Performance Duty Level specified, and:” 12/31/14   2002
9 267 9.4.6.9.2.2.1.2.1 - New Add new Item: “Blocking size and location to be as specified.” 12/31/14   2002
9 267 9.4.6.9.5.2 Change Item number from 9.4.6.9.5.2 to 9.4.6.9.5.3. 12/31/14   2039
9 267 9.4.6.9.5.2 - New Add new Item: "For TRANSPARENT finish to be:      
9 267 9.4.6.9.5.2.1 - New Add new Item: “Of a species compatible in color with the face veneer” with a bolded “C” for Custom Grade. 12/31/14   2039
9 267 9.4.6.9.5.2.2 - New Add new Item: “The same species as the face veneer” with a bolded “P” for Premium Grade. 12/31/14   2039
9 268 9.4.6.10.5.1.1.1 Change text to read: “Face laminations shall . . . “ 12/31/14   2023
9 269 9.4.6.10.6 Correct shaded numbers below which switch between 6 and 7. 04/29/16   2104
9 272 9.6.4.15.1.2 Bold the last digit of the Items reference number. 12/31/14   2013
10 298 14.1 - Corrected Correct the Item number from 10.1.1 to 10.1.14.1 12/31/14   2014
10 303 10.4.4.8.8.1 Change to read: “. . . lbs (91 kg). 7/31/15   2074
10 305 10.4.5.6.2.2 Change text to read: Plain sliced, except rotary at Birch. 04/29/16    
10 306 10.4.5.9.3.4.1.1.3 Eliminate 04/29/16   2106
10 306 10.4.5.9.3.4.1.1.3.1 Change to 10.4.5.9.6.4.1.1.3. 04/29/16   2106
10 306 10.4.5.9.3.4.1.1.3.2 Change to 10.4.5.9.3.4.1.1.4 and reword to read: “. . . veneer of minimum HPVA Grade C of manufacturer’s choice of species compatible to exposed surface.”” 04/29/16   2106
10 307 10.4.5.9.3.4.3.2.2.1 Change text to read: “. . . wider than 30” (762 mm).” 12/31/14   2044
10 308 10.4.5.10.3.2.3.2 - Corrected Correct the Item number from 10.4.5.10.3.2.3.1 to 10.4.5.10.3.2.3.2 and bold the last digit and change subsequent items numbers below. 12/31/14   2015
10 308 10.4.5.10.3.2.3.2.1.1 Change text to read: “. . . wider than 30” (762 mm).” 12/31/14   2044
10 310 10.4.7.2.4.1 Change all subsequent shaded reference to “4” below to “1” – for a total of six occurrences. 7/31/15   2075
10 314 10.4.7.8.10.3.1.1 Move to New Item 10.4.7.8.10.3.4 04/29/16   2110
10 314 10.4.7.8.10.3.2 Change to read: Tall storage cabinets with full height doors and fixed mid height shelf shall be equipped with elbow catch/latch and stop block on the inactive leaf at the fixed shelf. 04/29/16   2110
10 314 10.4.7.8.10.3.3 Change to read: Tall storage cabinets full height doors; however, without fixed mid height shelf shall be equipped with elbow catch/latch with spring actuated chain bolt with shelf depth adjusted accordingly. 04/29/16   2110
10 316 10.4.7.11.2.3 - Corrected Correct the Item number from 10.4.7.11.2.4 to 10.4.7.11.2.3 and all subsequent numbering. 12/31/14   2016
10 316 10.4.7.11.2.3 Change text to read: “. . . 40 lb per sq ft (195.3 kg/m2) load . . . “ 12/31/14   2030
10 316 10.4.7.11.2.3.1 Change text to read: “A 50 lb per sq ft (244.1 kg/m2) load . . . “ 12/31/14   2030
10 317 10.4.7.14.5 Change text to read: "... case body and nailed or stapled to divisions ..." 12/31/14   2120
10 317 10.4.7.14.6 Change text to read: "... case body and divisions and/or fixed shelves at a minimum ..." 04/29/16   2121
10 318 10.4.7.16.9.1.4.1 Eliminate 04/29/16   2115
10 318 10.4.7.15.7 Change text to read: “:. . . doors above that is the minimum width as to operate without binding of contact.” 12/31/14   2008
10 321 10.4.7.20.1.1 Change text to read: “Be securely glued.” 12/31/14   2005
10 321 10.4.7.20.2.1 Change previous Errata to read "... on center at the top long edge." 04/29/16   2089
10 321 10.4.7.20.1.2 - New Add new Item: “Top anchor strip must be mechanically fastened at a maximum of 4” (101.6 mm) on center.” 12/31/14   2005
10 322 10.4.7.22.3.1.5.4 - New Add/insert new Item 10.4.7.22.3.1.5.4: “If less than 6-1/2” (241.3 mm) wide than maximum spacing shall not exceed 2-1/2” (63.5 mm). Old Item 10.4.7.22.3.1.5.4 is being changed to 10.4.7.22.3.1.5.5. 7/31/15   2054
10 322 10.4.7.22.3.1.5.4 Change original Item 10.4.7.22.3.1.5.4 to 10.4.7.22.3.1.5.5. and change dimension on top of illustration from 3-21/32” to 3-25/32” 7/31/15   2054
10 322 10.4.7.22.3.1.6.5 Change to read: “. . . on center, unless joint is less than 12” (304 mm) maximum spacing shall not exceed 4” (101.6 mm). 7/31/15   2054
10 322 10.4.7.22.4 – New Add new Item: “Joinery other than that provided for within Section 10 is permitted provided it is fully documented in a text/illustration explanation, and each material application has been independently tested to show compliance to the minimum requirements of the Cabinet Structural Integrity Tests within the APPENDIX. 12/31/14   2026
10 323 10.4.7.2.2.1 Change to read: “Are NOT ALLOWED. 7/31/15   2061
10 323 10.4.7.23.4 Change to read: ” Up to 96” (2438 mm) in length requires one piece, up to 192” (4877 mm) in two equal lengths, or up to 288” (7315 mm) in three equal lengths, and so on.” 04/29/16   2122
10 323 10.4.7.25.1 Change text to read: “EDGE ALLIGNMENT of doors . . . “ 12/31/14   2031
10 326 10.4.7.28.3.3.2 Change text to read: "...shall be of the same thickness and material as the exterior faces."EDGE ALLIGNMENT of doors . . . “ 04/29/16   2112
10 328-332 10.6.1 Basic Rules Change column header to read: “10.6.4 Basic Rules 7/31/15   2086
10 329 10.6.1.8 Drawing replaced with: 12/31/14   2031
10 331 10.6.1.13.5 - Corrected Change the Item number from 10.6.1.13.6 to 10.6.1.13.5 and all subsequent numbering. 12/31/14   2017
10 331 10.6.1.13.6 - Corrected Change the Item number from 10.6.1.13.7 to 10.6.1.13.6 and all subsequent numbering. 12/31/14   2018
11 343 Left Column In the left column, first bullet under the heading GUIDELINES FOR FABRICATION/INSTALLATION OF HPDL COUNTERTOPS change the word “comers” to “corners”. 7/31/15   2058
11 353 11.4.5.3.2 Eliminate the grade rule boxes 12/31/14   2022
11 353 11.4.5.3.2.1 Add the missing grade indicator letters with the E for Economy Grade bolded. 12/31/14   2022
11 353 11.4.5.3.2.2 Add the missing grade indicator letters with the C and P for Custom and Premium Grades bolded. 12/31/14   2022
11 354 11.4.5.8.1 Change text to read: “Nominal 1/4” (6.4 mm) . . . “ 12/31/14   2048
11 354 11.4.5.8.2 Change text to read: “Nominal 1/2” (12.7 mm) . . . “ 12/31/14   2048
11 355 11.4.6.7 Change text to read: 11.4.6.8 along with all of the subsequent shaded references to "7" below such to "8." 04/29/16   n/a
11 356 11.4.6.8 Change text to read:11.4.6.9 along with all of the subsequent shaded references to "8" below such to "10". 04/29/16   n/a
11 356 11.4.6.9 Change text to read:11.4.6.10 along with all of the subsequent shaded references to "9" below such to "9". 04/29/16   n/a
11 356 11.4.6.10 Change text to read: 11.4.6.11 04/29/16   n/a
11 359 11.4.7.19.2.1 Eliminate 04/29/16   2115
11 365 11.6.4.8 - Corrected Change the second 11.6.4.7 to 11.6.4.8 and bold it and all subsequent numbering. 12/31/14   2019
11 365 11.6.4.9 - Corrected Change 11.6.4.8 to 11.6.4.9 and all subsequent numbering. 12/31/14   2019
11 365 11.6.4.10 - Corrected Change 11.6.4.9 to 11.6.4.10. 12/31/14   2019
11 365 11.6.4.11 - Corrected Change 11.6.4.10 to 11.6.4.11. 12/31/14   2019
11 365 11.6.4.12 - Corrected Change 11.6.4.11 to 11.6.4.12. 12/31/14   2019
11 365 11.6.4.13 - Corrected Change 11.6.4.12 to 11.6.4.13. 12/31/14   2019
11 366 11.6.4.14 - Corrected Change 11.6.4.13 to 11.6.4.14 and all subsequent numbering. 12/31/14   2019
11 366 11.6.4.14.3.2.2 - Corrected Change 11.6.4.14.3.2.1 to 11.6.4.14.3.2.2. 12/31/14   2020
11 366 11.6.4.14.3.2.3 - Corrected Change 11.6.4.14.3.2.2 to 11.6.4.14.3.2.3. 12/31/14   2020
11 366 11.6.4.14.4 - Corrected Change 11.6.4.14.3 to 11.6.14.4 and all subsequent numbering. 12/31/14   2020
11 366 11.6.4.14.5 - Corrected Change 11.6.4.14.4 to 11.6.14.5 and all subsequent numbering. 12/31/14   2020
11 366 11.6.4.15 - Corrected Change 11.6.4.14 to 11.6.4.15 and all subsequent numbering. 12/31/14   2019
11 366 11.6.4.16 - Corrected Change 11.6.4.15 to 11.6.4.16 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.17 - Corrected Change 11.6.4.16 to 11.6.4.17 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.18 - Corrected Change 11.6.4.17 to 11.6.4.18 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.19 - Corrected Change 11.6.4.18 to 11.6.4.19 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.20 - Corrected Change 11.6.4.19 to 11.6.4.20 12/31/14   2019
11 367 11.6.4.21 - Corrected Change 11.6.4.20 to 11.6.4.21 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.21.2 Change text to read: “. . . shall be used at miter and butt joints . . .” 12/31/14   2051
11 367-8 11.6.4.22 - Corrected Change 11.6.4.21 to 11.6.4.22 and all subsequent numbering. 12/31/14   2019
11 367 11.6.4.22.3.3 - New Add new Item 11.6.4.22.3.3: “Mechanical Fasteners are required between splash members and deck. 7/31/15   2050
11 368 11.6.4.23 - Corrected Change 11.6.4.22 to 11.6.4.23 and all subsequent numbering. 12/31/14   2019
11 369 11.6.4.24 - Corrected Change 11.6.4.23 to 11.6.4.24 and all subsequent numbering. 12/31/14   2019
11 369 11.6.4.24.2 Correct spelling of “silcon” to “silicone”. 7/31/15   2034
11 369 11.6.4.24.4 - New BACK and END SPLASHES shall be securely adhered to the wall, butt joined to the countertop, and shall be: 7/31/15   2034
11 369 11.6.4.24.4.1 - New CAULKED with clear or compatible color waterproof caulking (furnished by the installer) so as to leave a visual bead not exceeding 1/8” (3.2 mm) between the bottom of the splash and the countertop. 7/31/15   2034
11 369 11.6.4.24.4.2 - New Variation in building walls in excess of 1/2” (12.7 mm) in 144” (3658 mm) may result in gaps between splash and walls and shall not be considered a defect or the responsibility of the installer. 7/31/15   2034
11 369 11.6.4.25 - Corrected Change 11.6.4.24 to 11.6.4.25 and all subsequent numbering. 12/31/14   2019
11 369 11.6.4.25.1.3 – Corrected Change 11.6.4.25.1.4 to 11.6.4.25.1.3. 12/31/14   2021
A 391 Heat Resistance Test Eliminate 04/29/16   2115
Dl 423 Second paragraph in center column Change last sentence to read: “the 19th Century saw continued Classicism, but also, , , “. 12/31/14   2057
G 491 Balanced Construction Change last sentence to read: . . . on the other hand, require some form of backer material.”. 12/31/14   2033
G 502 Immediaely following "PANEL MATCH" Add note stating: "PANEL REVEAL, see lower right corner" 04/29/16   2087
G 504 "REVEAL, PANEL" Rename PANEL REVEAL and move to page 502 at lower right corner, leaving a note that states “REVEAL, PANEL: Renamed PANEL REVEAL and move to page 502” 04/29/16   2087
G 505 At "Scribe" Add note “See Filler, Mold, and Allowance on page 509” 04/29/16   2087
G 509 After "Worm Track" Add note and new terms and definitions: The following belongs on page 505 however, are placed here for efficiency. SCRIBE FILLER: A scribe filler is used to fill the space between a base or wall cabinet and an adjacent wall. The face of the scribe filler is typically set flush or a maximum of 1/16” (1.6 mm) set back from the face edge of the cabinet box. SCRIBE MOLD: A scribe mold is used to cover the space between a base or wall cabinet and an adjacent wall. The face of the scribe mold is typically set on top of the face edge of the cabinet box and not interfering with the door opening. SCRIBE ALLOWANCE: A scribe allowance is an amount added to the wall side of a cabinet face frame allowing the installer material to cut in order to achieve a tight fit to the wall. 04/29/16   2087